Jump to content


Toggle shoutbox Shoutbox - Chat with members! Open the Shoutbox in a popup

@  Surturiel : (05 July 2015 - 10:58 PM) oh, ok, Mike. wide® 15" it is. anything against aftermarket ones?
@  Mike T : (05 July 2015 - 09:14 PM) 16s will give better roadholding but a worse ride. Wider 15s will probably not affect ride at all because there is the same height of rubber between the rim and road as the stylelines, but the roadholding will improve a lot; however going to 16s of the proper size will lose a half inch of rubber, giving a worse ride....and a much higher potential for rim damage.
@  Mike T : (05 July 2015 - 09:11 PM) You can use 16s, it's just that they will be damage prone and you will need to use the recommended sizes or the circumferences will differ too much between front and rear axles and the ESP will create a huge problem. Aside from that, there is not room in the 450 wheel wells for oversized tires on 16 inch rims...the rears if 205 mm in width should be 45 series not 50. Fronts should be 175/50-16.
@  Surturiel : (05 July 2015 - 08:54 PM) (what did I get into..)
@  Surturiel : (05 July 2015 - 08:54 PM) is it THAT compllicated to get 16" wheels on a 450?
@  Surturiel : (05 July 2015 - 08:45 PM) 185/50 and 205/50 r16"
@  Mike T : (05 July 2015 - 07:45 PM) You can't use 185/50 and 205/50, the ESP will freak out and the car will be undriveable. I find that 175/55-15 front and 195/50-15 rear to be the best compromise between ride and handling.
@  marchanna : (05 July 2015 - 06:31 PM) LED headlights installed
@  Surturiel : (05 July 2015 - 05:59 PM) right now I have the Stylines with 145/55 front and 175/50 rear. I find the car skitterish on the highway and the ride is kinda harsh. I was considering 16"s with 185/50 front and 205/50 back, on the Trilines. possible? Would that improve both the comfort and stability?
@  Mike T : (05 July 2015 - 04:46 PM) If you are concerned about rim damage due to rough roads, don't even consider 16s.
@  Francesco : (05 July 2015 - 04:18 PM) I think the Monoblock VI is soft, not sure if other OE smart/BRABUS rims are. Afaik the smart and BRABUS rims are all OEMd by Ronal or ATS.
@  Surturiel : (05 July 2015 - 11:41 AM) and what about the trilines?
@  dmoonen : (05 July 2015 - 06:48 AM) I had 17" on the rears. bra is rims are soft as butter. Had to get mine straighten out twice in a three year span
@  Surturiel : (05 July 2015 - 02:26 AM) wider 15" then?
@  Surturiel : (05 July 2015 - 02:25 AM) So, no 16" wheels on a 450?
@  Mike T : (04 July 2015 - 10:35 PM) ...to avoid bent rims
@  Mike T : (04 July 2015 - 10:11 PM) 15" BRABUS wheels are fine. The 16s need more tire than the 450 can handle.
@  Surturiel : (04 July 2015 - 08:53 PM) on a 450
@  Surturiel : (04 July 2015 - 08:52 PM) smartmadness has 3x112 to 5x112 adapters, but they are 19mm thick. and I read that this is not enough for the rear wheels using OEM mercedes wheels
@  Surturiel : (04 July 2015 - 08:49 PM) So, no Brabus?
@  Mike T : (04 July 2015 - 08:47 PM) Used 16s out of Europe would be fraction of 3 grand. But the 16 inch BRABUS wheels are like bubble gum. Fairly warned be thee says I
@  Surturiel : (04 July 2015 - 08:47 PM) nope. there's no 6x112 pattern.
@  NelsonSmart : (04 July 2015 - 10:03 AM) There must be some 16"rims with 6 holes that could have the same offset that may work, that will take research/investigation
@  Surturiel : (04 July 2015 - 09:12 AM) any options on 16" wheels that don't end up costing almost 3k, then?
@  cadillacman : (04 July 2015 - 04:27 AM) the adaptors are going to act as a spacer kit, which will increase the offset, which will put a bit more stress on the bearings, we have delicate bearings
@  SmartED : (04 July 2015 - 04:15 AM) Going to the five lug application does improve your options in terms of wheel choices because there is a lot more out there. But, is it worth it? I don't know and I'm sure others more informed will join in.
@  Surturiel : (03 July 2015 - 04:01 PM) Question ( as usual) I'm investigating the whole 3 to 5 lug adapters for wheels. worth the time/investiment?
@  Surturiel : (03 July 2015 - 04:00 PM) hi, everyone
@  Mike T : (01 July 2015 - 06:36 PM) LOL
@  Mike T : (01 July 2015 - 06:36 PM) oops make that fogs
@  Mike T : (01 July 2015 - 06:36 PM) It's totally weird and you will have to cut the wiring. You are right not to use the OE smart fags, they are utter trash and the reflector melts after ten hours of use.
@  Surturiel : (01 July 2015 - 06:07 PM) question: (as usual) what kind of connector does the 450 fog light uses? I want to put an aftermarket fog light and don't want to cut the original wiring...
@  Mike T : (01 July 2015 - 10:13 AM) Good Canada Day eh?
@  Surturiel : (01 July 2015 - 10:08 AM) happy canada day!
@  SmartED : (01 July 2015 - 01:34 AM) Happy Canada Day everyone
@  Surturiel : (30 June 2015 - 09:14 PM) opinion: are those 3 to 5 stud adapters safe? I want a set of 16", but they're both hard to find and expensive...
@  Mike T : (30 June 2015 - 08:39 PM) *Jodhpur, damn fat fingers
@  Mike T : (30 June 2015 - 08:38 PM) *bolt
@  Mike T : (30 June 2015 - 08:38 PM) Take 'em off and three are three bold holes plus a large round one. Best to think of them as Jodphurs
@  Surturiel : (30 June 2015 - 07:57 PM) question: is there a way to remove those hip inserts?
@  FlossyTheSmart : (30 June 2015 - 05:14 AM) And that's without mentioning that compared to many cars, there were very few 450s made, and it's now 8 years out of production
@  FlossyTheSmart : (30 June 2015 - 05:12 AM) Well, I think you'll find it difficult to find ANY seat covers for a 450. There aren't a lot of offerings around
@  Surturiel : (29 June 2015 - 09:25 PM) on this topic, why is SO DAMN HARD to find leather seat covers for 450?
@  Surturiel : (29 June 2015 - 09:24 PM) sorry!
@  Mike T : (29 June 2015 - 09:19 PM) nor is it a leather seat!
@  Surturiel : (29 June 2015 - 07:52 PM) leather seat
@  Mike T : (29 June 2015 - 02:00 PM) This is not a search box!
@  mowser : (29 June 2015 - 11:42 AM) resetting the service reminder
@  mowser : (29 June 2015 - 09:53 AM) 299891
@  LeoBarbosa : (22 June 2015 - 06:03 PM) Just a feedback, the rear struts were really easy to do. Thanks for the tips. Payed $120 for both sides, at the dealership, in Calgary, AB.

Photo
- - - - -

450 CD Changer


  • Please log in to reply
No replies to this topic

#1 ogilvie

ogilvie
  • New Members
  • 2 posts
  • Location:Ottawa

Posted 31 January 2012 - 08:38 AM

We have 2 Brand New in Box CD Changers

#0003826V006000000 $693 Retail Asking $450.00 each

You can contact me by e-mail b.mcmillan@ogilviemotors.com or by phone : 613-745-9000




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users